Bryston Ltd. is a Canadian
company which has been designing and manufacturing state of the art specialty
electronics to both the professional and consumer audio marketplaces for over a
quarter century.Bryston has a major commitment to produce the most accurate and
reliable product available. We maintain an extensive research and development
division which is constantly looking for ways to improve the performance, value
and reliability of our products. We offer a full 20 Year transferable warranty,
parts and labour, on all our analog products. We offer a full 5 Year
transferable warranty on all our Digital circuits if purchased from an
authorized Bryston dealer. In the professional market we offer amplifiers
for recording studios, radio and television broadcast facilities and sound
reinforcement applications such as stadiums and arenas etc. In the consumer
market we manufacture state of the art audio electronics intended to provide the
owner with the most musically accurate and reliable performance available. Our
Service Centres contact information can be found here. Follow the latest news on
products in the Bryston Newsletter. To receive answers to Technical Questions
please click here. Bryston Authorized Dealer/Distributor Statement To Our Valued
Customers:WARNING: We urge you to use an authorized Bryston dealer or
distributor when purchasing a Bryston product.Bryston products are sold,
supported, and serviced through the worldwide network of dealers and
distributors listed in the Dealer/Distributor section of this website. If the
company selling Bryston product is not listed on this website, we encourage you
to e-mail Bryston to confirm whether or not the company selling the product is
part of the authorized Bryston network. Bryston does not authorize the sale of
current products online. When parties outside of the network of authorized
Bryston dealers and distributors sells a Bryston product, Bryston will not honor
warranties on those products.Proof of purchase in the form of a copy of the bill
of sale from an authorized Bryston Dealer/Distributor must be presented to
obtain warranty service. (This applies only to product manufactured after
February, 2006)
Listen
Past the equipment and Experience the music as Intended CONVENIENCE WITHOUT
COMPROMISE The challenge: to design an integrated audio amplifier with none of
the compromises usually associated with this approach. Our design team has
surpassed the challenge. The B-60 provides 60 watts per channel at 8 ohms and
100 watts per channel at 4 ohms. There are provisions for four high level inputs,
(CD, Tuner, Video and Aux) in addition to one tape loop and a pre-out/main-in
feature. A headphone jack is provided for those requiring monitoring and private
listening provisions. An optional motor driven volume remote control is also
available. This motorized volume approach ensures the lowest possible distortion
of the audio signal.Options Include:• Bryston Internal DAC • Bryston Internal MM
Phono Stage • Bryston handheld remote volume control HAND ASSEMBLED WITH CARE
Bryston hand assembles and individually tests each and everyproduct we
manufacture. We exclusively use only the finest components in our amplifier
designs, such as 1% metal-film resistors, polystyrene capacitors and hand
selected and matched transistors to reduce noise and distortion to the absolute
minimum. Bryston applies techniques and employs custom materials in our everyday
construction of electronic equipment that are more typically utilized in
military and aerospace industries. Our traditional adherence to proprietary
parts and sophisticated construction and testing techniques guarantees your
amplifier will perform for many years without concern. It also prevents any unit
to unit variability which inevitably is the result of any mass produced product.
PRE-OUT/MAIN-IN: A versatile feature on the Bryston B-60 integrated amplifier is
the pre-out/main-in connectors. It allows the independent use of the
preamplifier or stereo amplifier section within an audio or video system.
PERFORMANCE WITHOUT COMPROMISE With today’s increased clarity and dynamic range
in recordings and movie soundtracks you need equipment that not only equals but
surpasses the parameters of themost demanding material available. The Bryston
B-60 Integrated Amplifier is without peer in meeting this performance
challenge.4 stereo RCA inputs 1 stereo RCA output 1 stereo tape loop Headphone
output Gold plated switch, contacts and connectors Optional remote, volume and
mute Optional DAC Digital Circuits 5 Year Warranty Also Available with
Moving Magnet Phono Stage Available Now w/ Silver Faceplate
VERSIONE REMOTE
+500,00 EURO
The
Bryston B-100 SST Integrated Amplifier is without question one of the most
sonically transparent and reliable audio products available. It offers
performance levels equal to the finest separate audio components.The B100 SST is
a state of the art analog stereo integrated amplifier which utilizes ‘software’
control. The software allows us to provide many more features and functions
while still adhering to traditional fully discrete analog circuits throughout
the amplifier circuit path. The B-100 is available with an optional modular
plug-in Moving Magnet Phono stage (B-100P) as well as an optional plug in
Digital stage (B-100DA) for state of the art PCM Digital playback. Both the MM
Phono and the Digital stage are available separately or combined in a single
package. Modularity in design allows you to add either of these great options at
a later date if required. MODEL BP-100 SST C-SERIES INTEGRATED AMPLIFIERS B-100
Line level Integrated AmplifierB-100P Integrated Amplifier with MM Phono Stage
B-100DA Integrated Amplifier with 4 Digital inputs B-100P/DA Integrated
Amplifier with MM Phono and 4 Digital Inputs DESIGN PHILOSOPHY ENSURES SONIC
SUPERIORITY All signal circuitry is fully discrete to avoid the compromises,
phase shift and nonlinearities inherent in IC’s.Two completely separate and
independent custom torodial power supplies are employed to prevent any
possibility of channel to channel crosstalk or interference.Our unique
ultra-linear input buffer results in a substantial reduction in noise floor and
distortion.Gold plated five-way speaker binding posts and gold plated RCA input
and output connectors provide long-term trouble-free connections.Headphone
output on the front panel allows for monitoring and private listening.Full
function remote control (optional).High current reserves for lightning-fast
response.Programmable Pass-through feature.Digital Circuits 5 Year Warranty
20 Year Warranty - A Generation of Music
Varie versioni telefona per gli upgrade
PREAMPLIFICATORI STEREO
Bryston
BP-6 €.3.310,00
Per
prezzo scontato
TELEFONARE/EMAIL FOR
THE PURE & SIMPLE SOUND SYSTEM BP 6 C-SERIES PREAMPLIFIERS The Bryston BP-6
C-Series preamplifier is a simplified state of the art preamplifier offering 4
high level stereo inputs. Bryston’s BP-6 combines outstanding function with
complete musical accuracy. It provides an exact duplication of the original
recording experience, without distortion or coloration. Bryston proprietary
Class A Discrete Operational Amplifiers are used throughout. All signal
circuitry is fully discrete to avoid the compromises, phase shift and
nonlinearities inherent in IC’s. Controls are practical and convenient: source
switching, tape monitoring, mute, balance and volume. The BP-6 features four
high level inputs. Output is provided by two pair of single-ended RCA outputs. A
headphone output on the front panel allows for monitoring and private listening.
A motor driven volume up/down hand held remote control is also available as an
option if required. No internal wiring is designed into Bryston’s preamp
circuitry. Components plug directly into boards, eliminating variations in
signal travel and wire interaction. Volume controls are laser trimmed to within
1/4 dB accuracy for a firm image balance between the left and right channels.
Low output impedance and high current availability allow you to run long cables
between the preamp and power amp without any loss of frequency response, so you
can position your amp as close to your speakers as possible. The BP-6 is also
available with an optional internal MM Phono Stage (BP-6P) input or our now
famous Digital (DAC) input BP-6 DA if required. The BP-6DA has a coaxial S/PDIF
digital input . Anyone who is tired of the marginal sound quality coming from
the analog outputs of their CD or DVD player should strongly consider this
system. The Bryston DAC provides an easy upgrade path that will substantially
increase the resolution of your audio system.New C-Series cosmetics. 4 high
level stereo inputs. Optional Bryston internal DAC. Optional Bryston MM Phono
Stage. All signal circuitry is fully discrete to avoid the compromises, phase
shift and nonlinearities inherent in IC’s. Headphone output on the front panel
allows for monitoring and private listening. Optional volume up/down/mute remote
control (BP-6R). Hand held remote control can be added later if required.
Available in 17 or 19 inch C-Series faceplates in Silver or Black Technical
specifications identical to the B-60 integrated amp Digital Circuits 5 Year
Warranty
REDEFINING
INNOVATION BP 16 C-SERIES STEREO ANALOG/DIGITAL PREAMPLIFIER The new Bryston
BP-16 is based on our world famous B-100 SST integrated amplifier. In fact the
BP-16 is the identical preamplifier section from the B-100. Technical
specifications are identical to the B-100 amplifier section (see pg 8). This
provides a very cost effective solution for us to manufacture a full-featured
versatile preamplifier for our customers. The BP-16 is a state of the art analog
stereo preamplifier which utilizes ‘software’ control. The software allows us to
provide many more features and functions while still adhering to traditional
fully discrete analog circuits throughout the preamplifier. An example of how
innovative this new BP-16 is at maintaining the superiority of discrete analog
class A circuits while taking advantage of the ‘software control’ is in our new
digitally controlled volume. The digitally controlled volume utilizes a
resistance network on a chip. This technology, in reference to the signal path,
is still implemented in the analog mode. It offers many advantages, for instance
perfect channel balance, a simple integrated balance adjustment without
additional parts, practically zero adjustment noises, first class behavior in
reference to noise and distortion, as well as adjustment via software.MODEL
BP-16 C-SERIES PREAMPLIFIERS • BP-16 Line level Preamplifier • BP-16P
Preamplifier with MM Phono Stage • BP-16DA Line level Preamplifier with 4
Digital inputs • BP-16P/DA Preamplifier with MM Phono and 4 Digital Inputs
RS-232 Software Control/Upgradeable
IR Control New C-Series cosmetics Fully Discrete Analog Circuitry Relay
Switching on all Inputs 6 Analog Inputs and 4-Digital inputs (with DA version)
Record Loop Separate Power Supplies for Analog and Digital Sections Independent
grounds for Digital and Analog sections Two quick connect 12 Volt triggers – One
Programmable Programmable Pass-through feature New Volume Control Design
Headphone Jack Two Optical and Two SPDIF inputs (with DA version) Optional
Internal D to A Converter Optional Internal Moving-Magnet Phono Stage Optional
Full Function Remote Available in C-Series - Black or Silver 17” or 19”
faceplate Digital Circuits 5 Year Warranty
Bryston
BP-20 €.3.010,00
Per
prezzo scontato
TELEFONARE/EMAIL BP 20 Preamplificatore
stereo, 5 ingressi ad alto livello, 2 ingressi bilanciati, 1 uscita bilanciata,
2 uscite normali, barra per processore o registratore, frontale color argento.
Stadio fono MM opzionale.
BP
26 Preamplificatore stereo, 5 ingressi RCA, 2 uscite RCA, 2 ingressi bilanciati
XLR, 1 uscita bilanciata XLR, 1 barra di registrazione, uscita cuffie, contatti
placcati oro, telecomando, alimentazione MPS 2, frontale color argento.Opzioni
disponibili: Stadio fono MM, Stadio fono MM/MC, convertitore DAC con 2 ingressi
SPDIF.
Balancing
Art & Science for Musical Integrity BP26 SERIES PREAMPLIFIERS Bryston's BP26
series preamplifiers offer a significant step forward in capturing the
subtleties, nuances and emotions of recorded music. Designed inside and out to
reflect the improvements in the entire Bryston line, these preamplifiers are a
perfect match to our new SST series of amplifiers. All aspects of the signal
flow are greatly improved, with lower noise and distortion figures, and higher
overload levels. FEATURES INCLUDE Intermodulation distortion has been reduced to
less than .0015% from 20 to 20kHz. The noise floor has been significantly
improved, reducing background hash to far below audibility. Input to input
crosstalk is essentially nonexistant to eliminate signal bleed-through from one
source to another. Components plug directly into glass-epoxy circuit boards,
eliminating variations in signal travel and wire interaction.Signal switching
and audio connections utilize heavy gold plating to provide long-term
trouble-free connections. Gold plated balanced and unbalanced input and output
connectors are standard. A 12 volt AC/DC screw terminal connector on the rear of
the power supply provides for a convenient remote start feature available on all
Bryston amplifiers. All BP26 series preamplifiers are housed in steel cabinets
for shielding to reduce electromagnetic interference effects. Buffered inputs
provide for lower distortion and improved linearity from source components. A
ground plane has been incorporated in this new design to further reduce
crosstalk and noise throughout the internal circuitry. The power transformer is
mounted externally to eliminate power-supply noise interference. Each and every
BP26 series amplifier is assembled by hand and burned in for 100 hours to ensure
performance for many years to come. It is backed by a 20 Year Warranty -
unrivaled in the industry. Preamplifiers for the Music ConnoisseurTHE BRYSTON
BP26 SERIES OF AVAILABLE PREAMPLIFIERS: MODEL BP26 BP26 Line level preamplifier
with remote control BP26P Line level preamplifier with mm phono stage and remote
control BP26MC Line level preamplifier with mc, mm phono stage and remote
control BP26DA Line level preamplifier with 2 DAC inputs and remote control DAC
OPTION The new BP26 DA preamplifier provides a digital interface using premium
quality digital to analogue converters on 2 switchable stereo SPDIF inputs (RCA)
and Bryston's fully discrete Class A operational preamplifier sections. This
digital to analog option provides a state of the art upgrade path for customers
wanting to improve the digital capability of their stereo CD or DVD players.
Simply plug the digital out from your CD/DVD player into the Bryston BP26 DA.
The quality of sound using fully discrete Class A operational amplifiers, rather
than the typical IC's, has to be heard to be believed. REMOTE CONTROL FEATURE
The BP-26 version includes a remote control with motor driven volume up/down,
along with mute and absolute phase reversal buttons. Volume, mute and absolute
phase can also be activated manually on the front of the preamplifiers if the
need arises. MM/MC PHONO SECTION The huge library of music present on vinyl
represents an irreplaceable treasure. As such it becomes more important than
ever to reproduce the music with the greatest faithfulness to the original
recording Brystons unique and innovative Phono Section is available as an
optional built in feature in either moving magnet (BP26P) and/or moving coil
(BP26MC) version. It offers a broadcast quality uncomplicated package for those
who enjoy the ultimate in vinyl playback. Our feeling is that Bryston's BP26
series preamplifiers are one of those fortunate circumstances when the long
hours and extended listening pays off. The sense of transcending the recording
medium and experiencing the original performance is captured with exceptional
realism. We invite you to audition one today.5 stereo RCA inputs 2 stereo RCA
output 2 XLR inputs 1 XLR output 1 stereo tape loop Headphone output Gold plated
switch, contacts and connectors Remote, volume and mute Available with MM Phono,
MC Phono or DAC Digital Circuits 5 Year Warranty
Bryston
has a continuing commitment to design and manufacture the most accurate and
reliable audio product available. We maintain an extensive research and
development division which is constantly looking for methods to improve the
performance, value and reliability of our amplifiers. The Bryston 2B SST stereo
amplifier is the direct result of this continuing quest for perfection.NEW
STANDARDS OF ACCURACY:Bryston is pleased to introduce our new Bryston 2B-SST
C-Series 100 Watt per channel stereo amplifier. The first 2B started life way
back in 1979 and has become a Classic among discriminating audiophiles worldwide.
This latest version of our 2B incorporates all the new SST circuitry and
provides twice the power of our original 2B. From input to output, all the
circuitry in the 2B SST amplifier has been optimized for the most accurate
performance possible. The Bryston 2B SST amplifier is a compact, high quality
100 watt per channel, (8 ohms), stereo amplifier intended for use in home sound
systems requiring a musically accurate, extremely reliable, no compromise power
source.While the 2B has for years been thought of as an exceptionally lucid and
transparent amplifier for traditional two-channel stereo setups, it is now
finding additional acceptance in such installations as multimedia surround-sound
systems, and in the most ambitious music systems with multi-amplified speakers
using electronic crossovers.New
cosmetics 100 watts per channel 8 ohms, 180 watts 4 ohms, 350 watts
bridged 8 ohms New SST output devices Increased power supply capacitance -
30,000 MFD per channel Selectable Balanced or Unbalanced inputs Lower noise and
distortion Two New Independent ultra-low-noise power transformers New
computer modeled heat-sink design Quick connect remote 12 volt trigger
Selectable gain - 1 Volt or 2 Volt Available in Silver or black finish
with 19 or 17 inch faceplate 20 Year Warranty
Serious
Amplifiers for Serious Listeners: The 3B SST stereo amplifier, at 150 watts per
channel into 8 ohms and 250 at 4 ohms, provides all the quality and value of our
larger amplifiers but in a package which is both compact and powerful. Suitable
for a wide range of audio/video systems where sonic accuracy, medium power and
long term reliability is required. BRYSTON SST FEATURES:Membrane Power Switch
Soft start circuit on power up Multiple filter capacitance per channel
Selectable inputs for balanced or single ended (RCA) connectors Polarity Switch
(0 or 180 degrees) on each channel (6B & 9B only) Remote 12 Volt power trigger
input with delayed output feature Selectable gain settings Optional 17"
Faceplate (no handles) or 19 inch rack mount (with handles) available.
Optional Silver or Black Faceplate Available We invite you to experience the
Bryston SST Series amplifiers 20 Year Warranty -A Generation of MusicMembrane
Power SwitchSoft start circuit on power up Multiple filter capacitance per
channel Selectable inputs for balanced or single ended (RCA) connectors Polarity
Switch (0 or 180 degrees) on each channel (6B & 9B only) Remote 12 Volt power
trigger input with delayed output feature Selectable gain settings Optional 17"
Faceplate (no handles) or 19 inch rack mount (with handles) available. Optional
Silver or Black Faceplate Available
Audio
Legend: The Bryston 4B SST is something of a legend among audio amplifiers. As
our most popular it has attained international status as an amplifier suitable
for the finest and most sophisticated sound systems. Whatever the venue, be it a
recording studio stage, a broadcast facility, a home theater installation, or a
state-of-the-art stereo system, Bryston has continued to be the number one
choice. The 4B SST is a pure dual mono design and offers 300 watts per channel
into 8 ohms and 500 watts into 4 with over 1000 watts available in bridged mode.
BRYSTON SST FEATURES: Membrane Power SwitchSoft start circuit on power up
Multiple filter capacitance per channel Selectable inputs for balanced or single
ended (RCA) connectors Polarity Switch (0 or 180 degrees) on each channel (6B &
9B only) Remote 12 Volt power trigger input with delayed output feature
Selectable gain settings Optional 17" Faceplate (no handles) or 19 inch rack
mount (with handles) available. Optional Silver or Black Faceplate Available
Mission
Impossible: The 7B SST is a MONO block design capable of over 600 watts at 8
ohms and over 900 watts at 4 ohms. This gives the 7B ST the power to drive, with
breath-taking ease and clarity, speakers, which have been considered "impossible"
loads in the past. One advantage of the Mono design 7B SST is it allows you to
place the amplifier adjacent to the loudspeaker providing improved performance.
The 7B SST is available in either a Series or Parallel version. 'Series' is
recommended with loudspeaker loads above 3 ohms and 'Parallel' for loudspeaker
loads below 3 ohms. BRYSTON SST FEATURES: Membrane Power Switch Soft start
circuit on power up Multiple filter capacitance per channel Selectable inputs
for balanced or single ended (RCA) connectors Polarity Switch (0 or 180 degrees)
on each channel (6B & 9B only) Remote 12 Volt power trigger input with delayed
output feature Selectable gain settings Optional 17" Faceplate (no handles) or
19 inch rack mount (with handles) available. Optional Silver or Black Faceplate
Available
We invite you to experience the
Bryston SST Series amplifier 20 Year Warranty -A Generation of Music
Our
Mission To design a State of the Art, ultra high powered Dual Mono Amplifier.
The Bryston 14B SST is a balanced-output amplifier which reduces THD and IMD to
unprecedented low values, (typically 0.001% or less), for a new degree of
transparency, musicality and ease of listening. Superbly low noise floor,
typically below – 118dB, yields an inky black silence between notes for
hauntingly realistic reproduction. Tremendous power reserves give the 14B SST
virtually perfect freedom from overload on any type of speaker or music,
bringing the performance and realism directly into your listening environment.
The ability to resolve subtle details has to be heard to be believed – it truly
sets a new standard – mission accomplished. Features Available in both 240 Volt
10 Amp version or 120 Volt 15 or 20 Amp versions Over 100,000 MFD of filter
capacitance per channel Selectable gain Normal Balanced (2V), Balanced plus 6dB
(1V), Unbalanced (1V) Remote 12-Volt power trigger input Selectable
external power-up Membrane power switch Heat Sinks The Bryston 14B SST employs a
total new computer modeled heatsink design maximizing heat dissipation for
long-term “fan-free” operation into the most demanding speaker loads.
Independent Power Supplies The Bryston 14B SST is a 2-channel power amplifier
consisting of two totally independent amplifier modules, each with its own
inde-pendent power transformer equivalent to a +/- 120 Volt power supply. Each
audio channel provides connections for balanced or single ended input and will
supply a minimum of 600 watts of power into 8 ohms or 900 watts into 4 ohms.
Unique Burn-In Procedure: Each and every Bryston product undergoes a very
extensive “burn-in” procedure. Following a complete operational checkout, every
amplifier is placed on a test-bench and cycled on and off at one hour intervals
for 4 days at full output. This extremely rigorous burn-in quickly “matures”
components and weeds out any potential premature failures. The result is
reliable trouble-free performance for many years, and is backed by Bryston’s
exclusive 20-year full warranty. Sonic Superiority Hand Assembled With
Care: Bryston hand assembles and individually tests each and every product we
manufacture. We exclusively use only the finest components in our amplifier
designs, such as 0.1% metal-film resistors, polystyrene capacitors and hand
selected and matched transistors to reduce noise and distortion to the absolute
minimum. Bryston applies techniques and employs custom materials in our everyday
construction of electronic equipment that are more typically utilized in
military and aerospace industries. Our traditional adherence to proprietary
parts and sophisticated construction and testing techniques guarantees your
amplifier will perform for many years without concern. It also prevents any
unit-to-unit variability, which inevitably is the result of any mass produced
product. Design Philosophy Ensures Sonic Superiority: All analog signal
circuitry is fully discrete to avoid the compromises, phase shift and
non-linearities inherent in IC’s. Two completely separate and independent power
supplies are employed to prevent any possibility of cross-talk or interference.
Gold plated RCA and XLR input connectors provide long-term trouble-free
connections. There are two power switches on the 14B SST. The front panel SST
Power Switch and the rear panel On/Off Circuit Breaker.Performance Without
Compromise: With today’s increased clarity and dynamic range in recordings and
movie soundtracks you need equipment that not only equals but also surpasses the
parameters of the most demanding material available. The Bryston 14B SST Dual
Mono Amplifier is without peer in meeting this performance challenge.The
Consequence: Obviously the goal of all this technology is to transport you to
the scene of the movie or the location of the musical recording. Experiencing
all the drama, movement and emotions intended is the one and only true measure
of any audio/video system. We know you will agree the Bryston 14B SST Dual Mono
Amplifier provides you with an open window on the experience. If your
requirements are for sonic excellence in both analog and digital formats without
compromises in performance, value and reliability look no further than the
Bryston 14B SST Dual Mono Amplifier. We invite you to experience the
Bryston SST Series amplifiers 20 Year Warranty -A Generation of Music
Our
Mission To design a state of the art 1000 watt power amplifier that does
not compromise performance at 1/10th power. A significant part of the design
criteria for the 28B SST was to develop a very powerful amplifier that would
drive any speaker on the planet but maintain an ideal power curve at 1 watt as
well as at 1000 watts and every power level in between. Most amplifiers exhibit
a power curve whereby the best noise floor, drive capability and distortion is
maintained from about 1/3 power and up. The Bryston 28B-SST Mono amplifier
maintains its power curve right from the first watt. This results in a BIG
POWERFUL amplifier that sounds incredibly detailed and musical at very low
levels and maintains that same sophistication and drive capability with even the
most difficult, inefficient speakers, large or small. The Bryston 28B-SST is a
fully balanced output amplifier (BRIDGED), which has reduced THD and IMD to
unprecedented low values, (typically 0.001% or less), for a new degree of
transparency, musicality and ease of listening. Superbly low noise floor,
typically below – 115dB, yields an inky black silence between notes for
hauntingly realistic reproduction. Tremendous power reserves give the 28B-SST
virtually perfect freedom from overload on any type of speaker or music,
bringing the performance and realism directly into your listening environment.
The 28B’s ability to resolve subtle musical details has to be heard to be
believed – it truly sets a new standard : Mission accomplished. Features
Selectable input – balanced (xlr) or single ended (rca) Selectable gain - 1v =
29db or 2v = 23dB External power on off control - 12v trigger New micro
controlled soft start New power switch All A/C is totally shielded from
Audio circuits Maintains exceptionally low noise and distortio from very
low to very high power demands Heat Sinks The Bryston 28B-SST employs a total
new computer modeled heat sink design maximizing heat dissipation for long-term
“fan-free” operation into the most demanding speaker loads. Power Supply The
Bryston 28B-SST is a single channel mono block power amplifier capable of
delivering over 1000+ watts of power. To provide this power the 28B POWER SUPPLY
utilizes a 2000 VA custom power transformer, with 120,000 uf of filter
capacitance, supply rails of +/- 90v. The component layout has been optimized so
power path lengths are very short, and all wire has been eliminated after the
power transformer. Unique Burn-In Procedure: Each and every Bryston product
undergoes a very extensive “burn-in” procedure. Following a complete operational
checkout, every amplifier is placed on a test-bench and cycled on and off at one
hour intervals for 4 days at full output. This extremely rigorous burn-in
quickly “matures” components and weeds out any potential premature failures. The
result is reliable trouble-free performance for many years, and is backed by
Bryston’s exclusive 20-year full warranty.Hand Assembled With Care: Bryston hand
assembles and individually tests each and every product we manufacture. We
exclusively use only the finest components in our amplifier designs, such as 1%
and 0.1% metal-film resistors, polystyrene capacitors and hand selected and
matched transistors to reduce noise and distortion to the absolute minimum.
Bryston applies techniques and employs custom materials in our everyday
construction of electronic equipment that are more typically utilized in
military and aerospace industries. Our traditional adherence to proprietary
parts and sophisticated construction and testing techniques guarantees your
amplifier will perform for many years without concern. It also prevents any
unit-to-unit variability, which inevitably is the result of any mass produced
product. Design Philosophy Ensures Sonic Superiority: All analog signals are
delivered by fully discrete components. All critical transistors are closely
matched. All capacitors are selected for long life. All audio connectors are
gold plated, to be trouble free.Performance Without Compromise: With today’s
increased clarity and dynamic range in recordings and movie soundtracks you need
equipment that not only equals, but also surpasses the parameters of the most
demanding material available. The Bryston 28B-SST Mono Block Amplifier is
without peer in meeting this performance challenge. The Consequence:
Obviously the goal of all this technology is to transport you to the scene of
the movie or the location of the musical recording. Experiencing all the drama,
movement and emotions intended is the one and only true measure of any
audio/video system. We know you will agree the Bryston 28B-SST Mono Amplifier
provides you with an open window on the experience. If your requirements are for
sonic excellence in both analog and digital formats without compromises in
performance, value and reliability look no further than the Bryston 28B-SST Mono
Amplifier. We invite you to experience the Bryston SST Series amplifiers 20 Year
Warranty -A Generation of Music
BCD 1 Lettore CD, riproduzione CD e CDR, stadio di uscita in classe A, 192kHz /
24 bit, DAC Crystal, sovracampionamento 128x, alimentazioni digitale e analogica
indipendenti, uscite sbilanciate RCA e bilanciate AES EBU, uscite digitali,
uscita ottica, porta RS-232 per aggiornamento software, comando a distanza
(impartisce anche comandi di regolazione del volume agli altri apparecchi
Bryston), pannello frontale argento o nero, da 17 o 19".
The
Bryston BCD-1 is a State-of-the-Art Redbook CD player using fully discrete
analog Class-A proprietary Bryston circuits, a quality Drive, and a 192K/24Bit
Crystal DAC.The advantage of an all in one box solution for a CD Player (as
opposed to a separate outboard DAC and Drive) is the elimination of jitter. For
optimum performance the Drive and DAC must use the same MASTER CLOCK. If the
clock signal of the drive is not synchronized with the clock signal from the DAC
then jitter develops. In external DACs the digital input must be re-clocked in
order to reduce the jitter. Jitter is defined as mistiming of the digital signal.
The timing of all those ones and zeros is of extreme importance. It isn’t enough
to get the bits right; those bits have to be converted back into music with the
same timing reference as when the music was first digitized. These timing errors
(jitter) are the bane of quality audio. With the Bryston CD player the master
clock and the drive are synchronized perfectly to eliminate any possibility of
jitter affecting the sound quality of the player.The DAC integrated circuit
(chip) provides the conversion of the digital signal to the analog domain. The
chip used in the BCD-1 CD Player is a Crystal CS4398. The CS4398 is a hybrid
multi-bit delta-sigma DAC. This is a rather tongue-twisting description that
refers to an advanced generation chip using a combination of several different
methods to optimize the conversion process. This DAC uses a process to
over-sample the digital input 128 times. Over-sampling is when the samples are
re-read (2x, 4x, 8x, etc.) to create a new sampling frequency. The new samples
are then run through an interpolation filter to create a more analog-like
waveform. The output of this process is a very sensitive analog signal and it is
critical that the timing of this process is very closely controlled by a low
jitter clock.DAC chips also require a very clean digital power supply if they
are to function at their optimum. Noise on the digital supply may cause added
jitter, noise, and distortion. Incorrect circuit trace routing of the digital
power supply or ground may introduce digital noise into the analog circuits.
This digital power supply is provided from a separate closely regulated and
filtered source. The DAC also requires a high quality analog power source
because the analog signal is at its lowest magnitude when it enters and leaves
the DAC. As a result, any added noise or distortion will be greatly amplified by
later stages. Again a separate, heavily regulated and filtered power supply with
carefully routed grounds is provided. Finally, if a digital trace, signal or
power, is routed in a layer above or below an analog trace it can induce noise
via capacitive coupling. Careful trace routing eliminates these problems and
provides the extra dB’s of noise and distortion reduction which separates good
from outstanding equipment. This attention to detail with the power supplies is
one of the reasons for the superior sound of the BCD-1 Bryston CD Player.Getting
the Digital side of the equation correct is only the start. Once the signal
leaves the DAC it is buffered and increased in strength by operational
amplifiers. In the Bryston BCD-1 CD Player these are constructed from discrete
devices (individual transistors, resistors, and capacitors) instead of the
commonly used integrated circuits. The use of discrete devices allows the design
of a circuit that exactly matches the needs of the DAC. The use of integrated
circuits always involves compromises since they are designed as general-purpose
devices. Discrete devices also allow for more powerful outputs from operational
amplifiers since the heat from the output driver transistors is separated from
other devices. In an integrated circuit op amp this heat can affect the rest of
the circuitry since it is all on one chip.Discrete devices also allow specific
matching of important characteristics such as input and output impedances based
on the specific in-circuit requirements. Discrete operational amplifiers can
also be designed to more closely match their power source leading to additional
reduced distortion and noise. Discrete devices can be tested very closely to
meet specific tolerances and can be matched against each other when a desired
performance design is critical. Circuits can be and are designed to require
closely matched devices for optimum performance. Integrated circuits have large
numbers of components on one chip and it is not practical to do more than
high-level sorting of device characteristics. Bryston does sorting and grading
with its DAC chips but does so to a much finer level with the discrete devices,
which leads to superior sound quality.Bryston hand assembles and individually
tests each and every product we manufacture. We exclusively use only the finest
components in our products, such as 1% metal-film resistors, polystyrene
capacitors, and hand selected and matched transistors, in order to reduce noise
and distortion to the absolute minimum. Bryston applies techniques and employs
custom materials in our everyday construction of electronic equipment that are
more typically utilized by military and aerospace industries. Our traditional
adherence to the use of proprietary parts, sophisticated construction, and
refined testing techniques, guarantees that your Bryston CD Player will perform
superbly, without any problems, for many, many years. It also prevents any
unit-to-unit variance which inevitably is the result of any mass produced
product.With today’s increased clarity and dynamic range in recordings you need
equipment that not only equals but surpasses the parameters of the most
demanding material available. The Bryston BCD-1 CD Player is without peer in
meeting this performance challenge.Redbook CD and CDR playback Fully Discrete
Bryston Class A analog output stage Crystal 192k/24bit DAC Over-sampling is 128
times Independent Analog and Digital power supplies Balanced XLR and Unbalanced
RCA Stereo outputs Transformer coupled SPDIF and AES EBU Digital outputs Optical
output RS-232 software upgrade Remote 12 Volt Trigger Full function IR remote
control CD remote operates other Bryston products volume up/down/mute
Cosmetically matches C-Series BP26/MPS219
Stadio di conversione DA, doppio DAC Crystal 192kHz/24bit, doppia alimentazione
indipendente, sovracampionamento 32x a quadrupla velocità, upsampling sincrono
(176,4kHz/192kHz), percorsi di segnale analogico e digitale separati. Ingressi
USB (1), COAX (2), OPTICAL (2), AES-EBU (1), BNC (2). Campionamento 32, 44,1,
48, 88,2, 96, 176,4 e 192kHz, PCM 16-24bit, USB 16bit 32-48kHz, uscite
stereofoniche bilanciate XLR e sbilanciate RCA totalmente differenziali, uscita
bypass loop SPDIF COAX, aggiornamento software tramite RS-232, comando a
distanza opzionale, trigger 12 volt per l'utilizzo da remoto, compatibile con
meccaniche CD, schede audio, computer, server musicali. La cosmetica riprende il
design C-Series (BP26, MPS2, BCDm, ecc)
STATE-OF-THE-ART
The Bryston BDA-1 is a state-of-the-art external Stereo DAC (digital to analog
converter) using fully discrete Class-A proprietary Bryston analog circuits, two
independent linear power supplies and dual Crystal CS-4398 DAC chips. The BDA-1
features an impressive array of inputs for USB, COAX, OPTICAL, AES-EBU and BNC
equipped digital devices. For audio outputs, the BDA-1 offers both balanced XLR
as well as unbalanced RCA stereo connectors on the rear panel. The BDA-1 is
RS-232 software upgradeable, making it the most flexible high performance DAC on
the market. JITTER REDUCTION Jitter is a mistiming of data being moved from
point A to point B in any synchronous digital system. Think of jitter as
individual ticks on a clock—however each tick is not occurring at exact
one-second intervals. Some are slightly less than a second and some are slightly
longer, and they average out so that no actual time is being gained or lost over
a large number of seconds. Jitter is the difference between the shortest and the
longest second, and in digital audio systems this specification is usually
measured in nanoseconds. Both the frequency and the jitter characteristics of
the system’s digital clock will affect the accuracy of reproduction. The
frequency, if not accurate, can cause the pitch and speed of the music to change,
and in some systems cause drop-outs if there is no data available. THE BRYSTON
SOLUTION Bryston delivers superb sonic performance by re-sampling and
re-clocking the digital input in order to reduce jitter. The result, a
significant reduction in jitter (1/1000 of a nanosecond). But it isn’t enough to
just get the bits right; those bits have to be converted back into music with
the same timing reference as when the music was first digitized. The input
signal of the BDA-1 is re-clocked and re-sampled to reduce any possibility of
jitter affecting the sound quality. Even the input receiver and the sample rate
converter serve to further reduce jitter.IMPEDANCE MATCHING TRANSFORMERS The
best way to understand the Bryston BDA-1 External DAC is to follow the flow of a
signal from when it first arrives at the BDA-1 in digital form to when it leaves
to drive an external analog input. The digital signal first arrives at the BDA-1
via either the SPDIF COAX, OPTICAL OR AES EBU inputs or the USB interface input.
These are the standard digital outputs from a CD Drive, Sound Card, Computer,
Music Server etc. There are 6 digital inputs, which are easily selected using a
front panel switch. This digital signal contains data at over 1 million bits per
second that requires a bandwidth of 5 to 10 million hertz (cycles per second).
At these high frequencies, it is very important to maintain the quality of the
signal by having the correct termination at the digital inputs. The BDA-1
provides for this termination in the best possible manner using devices called
impedance matching transformers. Impedance matching transformers provide the
optimal interface to the incoming source under all sorts of signal conditions.
Lesser quality terminations will degrade the signal, causing increased
jitter.UPSAMPLING After the input stage, the signal goes to the SYNCHRONOUS
upsampling circuit (sample rate converter). This circuit converts the digital
signal from one sample rate and bit depth to another. In the BDA-1, the sample
rate is increased from the input sample frequency (32K, 48K, or 96K upsamples to
192K and 44.1K or 88.2K upsamples to 176.4K). The 16 bits of depth (the CD
standard) is increased to 24 bits. The added 8 bits are filled with placeholder
information. This upsampling process provides a digital signal for later
conversion to analog by the Crystal 4398 DAC chip. The upsampling process doesn’t
add any new, but does put the data in a form which can better be translated by
the DAC as described below. The advantage of this synchronous upsampling process
is improved processing of the upsampled signal by the DAC chip, which was
designed for higher sample rates and bit depths. There is also a noise shaping
process implemented where “noise” within the audible spectrum is shifted up to
frequencies above audible limits. An added advantage of this upsampling process
is that a totally new clock signal is applied, which results in significant
jitter reduction. OPTIONAL UPSAMPLING FEATURE A very unique feature of the
Bryston BDA-1 External DAC is the ability to disengage the upsampling feature.
You can compare an upsampled signal with a non-upsampled signal simply by
engaging a switch on the front panel. This feature is functional when using
sample rates of 44.1K, 88.2K, 48K, and 96K.BRYSTON DAC The DAC integrated
circuit (chip) provides the conversion of the digital signal to the analog
domain. The two independent DAC chip’s used in the BDA-1 are the Crystal
CS-4398. Due to the requirements of the conversion process, every DAC chip
employs a digital filter to the signal in the digital domain and an analog
filter after the conversion process has been applied. Without this upsampling
technology, these filters would likely effect frequencies at or near the audible
range, accompanied by unwanted level and phase changes. The CS-4398 is a hybrid
multi-bit delta-sigma DAC. This is an advanced generation chip, which uses
several methods to optimize the conversion process. This DAC uses a process
similar to the previously detailed upsampling process where it oversamples the
incoming signal. The CS-4398 operates in one of three oversampling modes based
on the input sample rate. Single-speed mode supports input sample rates up to 50
kHz and uses a 128x oversampling ratio. Double-speed mode supports input sample
rates up to 100 kHz and uses an oversampling ratio of 64x. Quad-speed mode
supports input sample rates up to 200 kHz and uses an oversampling ratio of 32x.
This again allows for filtering that is safely out of the audible range. The
output of this process is a sensitive analog signal. The timing of this process
must be very closely controlled by a low-jitter clock.POWER SUPPLY The stability
of power in any audiophile equipment is imperative to superb performance. The
BDA-1 uses two independent power transformers for the initial stages of
filtering and regulation. In the BDA-1, each stage in the digital chain (input
receiver > sample rate converter > digital audio converter) is independently
regulated to prevent any interactions and to provide a rock solid supply of
power for any up-sampling/over-sampling process. The Crystal DAC chip also
requires a very clean digital power supply if it is to function at its optimum
level. Noise on the digital supply could cause added jitter and various forms of
distortion. Incorrect circuit board routing of the digital power supply or
related ground may also introduce digital noise into the analog circuits. The
BDA-1’s digital power supply is provided from a separate closely regulated and
filtered source. The DAC also requires a high quality analog power source. The
analog signal is at its lowest magnitude within the DAC and as it exits the
chip, so any induced noise or distortion will be greatly amplified by circuitry
upstream from the DAC. Bryston engineers have employed a separate, heavily
regulated and filtered power supply with carefully routed grounds that is
critical to the superior sound of BDA-1. Careful trace routing eliminates the
risk of noise via capacitive coupling and provides the extra dB’s of noise and
distortion reduction which separate truly great audio equipment. DISCRETE
CLASS-A ANALOG STAGE The most critical part of the circuit design in the Bryston
BDA-1 is the DAC’s analog outputs—connected directly to a pair of proprietary
Bryston Class A discrete operational amplifiers rather than the typical IC chips
employed in most other products. These exotic amplifiers make a huge difference
in transparency, resolution and dynamic performance. The use of discrete devices
allows the design of a circuit that exactly matches the needs of the DAC,
whereas the use of general-purpose integrated circuits always involves
compromises. Discrete devices allow engineers to generate more output power
since the heat from the output driver transistors is physically separated from
other sensitive components. Discrete devices also allow specific matching of
important characteristics such as input and output impedances based on the
specific in-circuit requirements. Discrete operational amplifiers can also be
designed to more closely match their power source leading to additional reduced
distortion and noise. Bryston consistently utilizes discrete devices in our
product designs because our circuits are engineered to require closely matched
devices for optimum performance. Bryston does ultra-fine sorting and grading of
discrete devices, which leads to superior sound quality.HAND ASSEMBLED WITH CARE
Bryston hand assembles and individually tests each and every product we
manufacture. We exclusively use only the finest components, 1% metal-film
resistors, 0.1% polystyrene capacitors, and hand selected and matched
transistors in order to reduce noise and distortion to the absolute minimum.
Bryston applies techniques and employs custom materials in our everyday
construction of electronic equipment that are typically utilized by military and
aerospace industries. Our traditional adherence to the use of proprietary parts,
sophisticated construction, and refined testing techniques guarantees that the
Bryston BDA-1 DAC will perform superbly for many years. PERFORMANCE WITHOUT
COMPROMISE Bryston has always maintained that the final arbiter of this exercise
is to provide products that are as transparent and accurate to the original
recorded performance. The BDA-1 DAC is the ultimate representation of this
design goal. SPECIFICATIONS Frequency response - 20 Hz - 20 KHz -.1dB
Signal to noise – Audio Precision AP2700 analyzer FFT digital measurement 140 dB
unweighted THD plus noise - .002% IMD - .002% Jitter – below the
measurement capability of the AP2700 analyzer Output Level - 2.3V
unbalanced - 4.6V balanced Shipping weight - 18 Lbs / 8.2 Kg
Dimensions - 17 or 19 w / 11.25 d / 1.75 h inches 43.2 or 48.3 w / 28.6 d
/ 4.4 h cm We invite you to experience the Bryston SST2 Series amplifiers
20 Year Warranty - A Generation of Music
Finalmente è disponibile il tanto atteso
pre-processore sonoro Bryston SP3 Dopo anni di attesa finalmente Bryston ha reso
disponibile SP3, il pre-processore che si presta a diventare uno dei più
importanti riferimenti nell'industria; oggi è finalmente possibile utilizzare il
medesimo apparecchio per ottenere un risultato eccellente sia nell'ascolto
stereofonico della musica sia nella riproduzione multicanale delle colonne
sonore. Il "Surround Processor / Preamp" di Bryston è caratterizzato da un suono
tipicamei un'ottima trasparenza, ricco di dettagli e generoso nell'interezza di
tutto lo spettro sonoro, veloce e preciso nelle articolazioni più complesse che
sa suonare tenue o fragoroso, seguendo scrupolosamente le istruzioni dettate dal
materiale sorgente. Bryston SP3 è un pre-processore privo di compromessi idoneo
a qualsiasi configurazione; lo vanno a testimoniare l'impressionante numero di
connettori che albergano sul pannello posteriore del telaio: otto ingressi
analogici (sei coppie sbilanciate e due ingressi bilanciati), dieci ingressi
digitali (tra coassiali, ottici, xlr e usb), ben ventisei uscite analogiche
(dieci bilanciate e sedici sbilanciate) e tre uscite digitali (due HDMI e una
Toslink). La costruzione è anch'essa al top, utilizzando materiali e circuiti
selezionati, tra i quali spicca il Processore Sonoro Digitale TI DA710,
affiancato da conversioni AD e DA a 24 bit @ 192 kHz Delta-Sigma e dal software
proprietario dell'apparecchio che oltre a consentire praticamente qualsiasi tipo
di decodifica, incluse DTS-HD Master Audio™ e Dobly TrueHD™, permette modalità
di ascolto custom in grado di derivare suono multicanale da materiale a due
canali, come STEREO7, NEO:6 MUSIC e NEO:6 CINEMA, con configurazioni fino a otto
altoparlanti e due subwoofer. Ricordiamo inoltre che è ancora in corso la
promozione "Valutazione Speciale per il tuo vecchio Bryston SP", dove riportando
un Bryston SP1, SP1.7 o SP2 si avrà diritto a un buono sconto sull'acquisto del
Bryston SP3 rispettivamente di 910, 1.820 e 2.700 euro. La promozione termina il
31 Dicembre 2011 ed è valida presso qualsiasi rivenditore autorizzato Audio
Reference. Per conoscere il rivenditore autorizzato più vicino consulta la
sezione "Rivenditori Audio Reference" oppure contattaci con uno dei metodi
elencati alla pagina "Contatta Audio Reference". CARATTERISTICHE TECNICHE
Conversione A/D: 24 bit, 192 kHz Delta-Sigma Conversione D/A: 24 bit, fino a 192
kHz, Delta-Sigma DPS: TI DA710 Alimentazione: Alimentatore separato "off-line
standby" e alimentatore principale lineare con trasformatore toroidale che
utilizza multipli stadi di regolazione Risposta in frequenza: da 20 Hz a 20 kHz,
+/- 0,25dB Risonanza+Rumore: Livello di ingresso: 2Vrms nelle modalità DSP,
4Vrms nella modalità Bypass Impedenza d'ingresso: 50 kOhm per audio analogico
single ended, 1 kOhm per gli ingressi analogici bilanciati Livello di uscita:
8Vrms (16Vrms in bilanciato) nelle modalità DSP; 10Vrms (20Vrms in bilanciato)
nella modalità Bypass Impedenza di uscita: 110 Ohm Gestione delle basse
frequenze: 5 filtri passa alto di secondo ordine, filtro passa basso di quarto
ordine con una frequenza di taglio di 40-200 Hz Consumo: Massimo consumo 60
Watt, consumo in Standby inferiore a 1 Watt Ingressi analogici: 4 coppie stereo
single ended / sbilanciate (CD, Sintonizzatore, Satellite, DVD), 2 coppie single
ended sbilanciate ingressi tape (RCA), 2 coppie di ingressi bilanciati XLR
(femmina) Ingressi digitali: 4 coassiali RCA 75 Ohm SPDIF, 3 ottici Toslink, 2
AES/EBU XLR 110 Ohm, 1 USB 2.0 tipo B Uscite analogiche: 10 XLR (maschio)
bilanciate: Sinistro, Centrale, Destro, Sinistro Surround, Destro Surround,
Sinistro Posteriore, Destro Posteriore, Sinistro Ausiliare, Destro Ausiliare e
Subwoofer, 16 single ended sbilanciate RCA: Sinistro, Centrale, Destro, Sinistro
Surround, Destro Surround, Sinistro Posteriore, Destro Posteriore, Sinistro
Ausiliare, Destro Ausiliare e Subwoofer, 4 uscite tape, 2 uscite Zona Due Uscite
digitali: 2 HDMI, 1 Toslink ottica Trigger: un ingresso 12V, e uscite trigger
programmabili Porte dati e controllo: 1 sensore a infrarossi, ricevitore per il
telecomando, 1 mini jack phone da 3mm (2 conduttori) per ingresso dati di
controllo infrarossi ausiliario, 1 ethernet RJ45 per dati bilaterali,
scaricamento software, ecc Telecomando: 30 tasti, due batterie AAA Dimensioni
fisiche (LxAxP in mm): 432 x 146 x 362 (senza considerare manopole, piedini di
gomma e connettori), 432 x 156 x 391 (considerando manopole, piedini di gomma e
connettori). Disponibile anche con pannello largo 19" (483mm) Peso: circa 10kg
Temperatura massima del telaio: 50 gradi Celsius
With
the SP 2, we have sought to design an uncluttered, easy-to-use processor/preamplifier,
incorporating stereo and a full range of surround sound capability, which
delivers state-of-the-art performance in both analog and digital formats.
PERFORMANCE WITHOUT COMPROMISE With today’s increased clarity and dynamic range
in recordings and movie sound-tracks you need equipment that not only equals but
surpasses the parameters of the most demanding material available. The SP 2
preamplifier/processor is without peer in meeting this performance challenge.
EASY TO USE The Bryston SP 2 is the first high-end processor designed to make
home theater easy for the non-technical user. For example, most functions are
automatic, controls are well-labeled, and there are clear unambiguous LCD and
LED displays. Step-by-step set-up menus with error messages displayed on the LCD
window, and a user-friendly, yet comprehensive user manual, make the initial
set-up simple and straightforward. HOME THEATRE PROCESSING In the digital mode,
the SP 2 automatically detects the digital input signal, routes the signal
through the DSP module, and adjusts to the appropriate mode. The digital circuit
provides decoding for Dolby Digital, Dolby Prologic, DTS and THX formats, in
5.1, 6.1 and 7.1 channels. There’s also Mono and Stereo Down-mixing for all
modes, Bass Management modes for all speaker setups. ANALOG AND DIGITAL
CONTROL The SP 2 puts you in control of a full range of input/output
options, allowing a choice of 13 sources, with 6 digital inputs (4 - coaxial & 2
- TOSLINK; pro model, AES/EBU - 12 sources), 6 stereo analog inputs, and a set
of 6 inputs for a 5.1 analog output DVD-AUDIO player. A Digital toggle button
lets you switch easily between digital and analog input signals, and there is a
built-in 24/96 D/A processor. The SP 2 provides both unbalanced outputs (RCA)
and a set of 6 true balanced outputs (XLR) for 5.1 and stereo, each with its own
discrete output amplifier. Balanced signal transmission uses com-mon- mode
rejection to prevent induced hum and interference even with long cable runs.
STEREO PREAMPLIFICATION While the SP 2 is a great multi-channel
controller, there are those who still like their stereo in the analog realm; so,
at the touch of a button, the digital circuitry can be bypassed and SP 2
operated as a Bryston audiophile-quality analog pre-amp. The bypass mode
provides a totally discrete analog signal path — including an analog volume
control. The signal does not go through any IC’s or digital circuitry from input
to output. DIGITAL SIGNAL PROCESSING FOR MUSIC The SP 2 ’s DSP music
modes allow you a range of options to enhance the acoustic ambience of your
listening room: Stereo, Natural, Club, Stadium, Hall, Theatre, Church, and
Party. SONIC SUPERIORITY BY DESIGN The Bryston Design philosophy
ensures sonic superiority. All analog signal circuitry is fully discrete to
avoid the phase shift and nonlinearity inherent in ICs. We exclusively use only
the finest components, such as 1% metal-film resistors, polystyrene capacitors,
hand-matched transistors, and gold-plated RCA and XLR connectors to reduce noise
and distortion to the absolute minimum. Two completely sepa-rate and independent
power supplies are employed to prevent any possibility of digital to analog
crosstalk or interference. THE RESULT Of course, the purpose of all
this technology is to place you within the scene of the movie, or to transport
you to the actual musical event. Whether you can experience all the drama,
movement, and emotions intended is the one truly meaningful measure of any
audio/video system. Take the time to visit your Bryston dealer and audition the
Bryston SP 2 preamplifier/processor. We think that you’ll redis-cover how
exciting audio can be. Reliability & Support BUILT TO LAST Bryston
applies techniques and employs custom materials in our everyday construction of
electronic equipment that are more typically utilized in military and aerospace
industries. Our traditional adherence to proprietary parts and sophisticated
construction and testing techniques prevents the unit-to-unit variability
typical of mass produced product and assures that your amplifier will perform
for many years without concern. HAND ASSEMBLED WITH CARE All audio products we
make are hand assembled and individu-ally tested by a dedicated team of Bryston
employees in our own North American manufacturing facility. UNIQUE BURN-IN
PROCEDURE Each and every Bryston audio product undergoes an extensive quality
control “burn-in” procedure. Following a complete oper-ational checkout, every
unit is placed on a test-bench and run for 100 hours. This extremely rigorous
burn-in quickly “matures” components and weeds out any potential premature
failures. The result is reliable trouble-free performance for many years.
ON-LINE CUSTOMER SUPPORT The Bryston website allows for downloading of technical
bulletins, product addendums, and complete user manuals. OUR 20-YEAR WARRANTY
Our commitment to build-quality and to quality control is why every product we
manufacture features an unlimited, transferrable 20-Year Warranty, a warranty
that remains unequaled by any other audio manufacturer in the world. Digital
Circuits 5 Year Warranty 20 Year Warranty - A Generation of MusicAnalog and
Digital preamp with surround processor 5.1 analog bypass unit 7.1 channel RCA
outputs for EX and ES modes 96kHz digital input sample rates DTS NEO 6 Matrix
decoding THX™ Surround EX decoding Dolby Pro Logic II decoding Additional
2-channel music and surround modes
AMPLIFICATORI MULTICANALI
Bryston
875 HT €.10.960,00
Per
prezzo scontato
TELEFONARE/EMAIL The
new Bryston 875 HT amplifier represents a state-of-the-art approach to the
expanding home theater marketplace. Providing all the features and flexibility
necessary to assemble a superb Home Theater Multi-Channel Surround System. The
world famous all new SST technology is implemented throughout the 875 HT
amplifier providing the sound quality and incredible flexibility Bryston is
famous for. The amplifier offers 8 channels of amplification which can be
utilized as independent 75 watt modules or any 2 adjacent channels bridged to
250 watts. FLEXIBLE OPTIONS WOULD INCLUDE: 7.1 surround system incorporating 7
channels at 75 watts and 1 subwoofer channel at 75 watts 6.1 surround system
incorporating 6 channels at 75 watts and one subwoofer channel at 250 watts 5.1
surround system incorporating 3 channels (left/center right) at 250 watts and 2
surround channels at 75 watts 7.1 surround system incorporating 250 watts x 4
for surrounds and two back speakers with an additional 3 channel amplifier (Bryston
6B SST) for the front Left/Center Right speakers. 20 Year Warranty -A Generation
of MusicGold Plated 5-way speaker binding posts Switched Balanced (XLR) or
Single Ended (RCA) inputs Level controls on each channel 12 Volt power trigger
Ideal companion to the SP1.7 processor
Effortless
Power: The Bryston 6B SST is a single chassis power amplifier consisting of
three totally independent amplifier modules, each with its own power transformer
and power supply. Each audio channel provides connections for balanced or single
ended input and will supply effortless power to the world's most demanding
loudspeakers. The 6B SST is a new modular design from Bryston packaged in a
convenient single chassis. Each modular channel contains all the electronic
circuitry, connections and independent power supply. The chassis simply provides
Soft-Start AC to each channel, and a separate power LED illuminates on the front
panel indicating individual channel power status. The Byston 6B SST provides 3 X
300 watts per channel at 8 ohms or 3 X 500 watts per channel at 4 ohms. Three
completely separate and independent power supplies are employed to prevent any
possibility of channel to channel cross-talk or interference. BRYSTON SST
FEATURES: Membrane Power Switch Soft start circuit on power up Multiple filter
capacitance per channel Selectable inputs for balanced or single ended (RCA)
connectors Polarity Switch (0 or 180 degrees) on each channel (6B & 9B only)
Remote 12 Volt power trigger input with delayed output feature Selectable gain
settings Optional 17" Faceplate (no handles) or 19 inch rack mount (with handles)
available. Optional Silver or Black Faceplate Available We invite you to
experience the Bryston SST Series amplifiers 20 Year Warranty -A Generation of
Music
Overdrive:
The Bryston 9B SST is a hand-crafted, modular, single-chassis 5-channel power
amplifier delivering 140 watts per channel at 8 Ohms, and 200 watts at 4 Ohms.
Each modular channel contains all the electronic circuitry connections and
independent power supply, necessary to deliver the best possible sonic quality.
The chassis simply supplies AC and five power LED's on the front panel
indicating each channel's functional status, (green for power-on, red for
overdrive).BRYSTON SST FEATURES: Membrane Power Switch Soft start circuit on
power up Multiple filter capacitance per channel Selectable inputs for balanced
or single ended (RCA) connectors Polarity Switch (0 or 180 degrees) on each
channel (6B & 9B only) Remote 12 Volt power trigger input with delayed output
feature Selectable gain settings Optional 17" Faceplate (no handles) or 19 inch
rack mount (with handles) available. Optional Silver or Black Faceplate
Available We invite you to experience the Bryston SST Series amplifiersSoft
start circuit on power up Multiple filter capacitance per channel Selectable
inputs for balanced or single ended (RCA) connectors Polarity Switch (0 or 180
degrees) on each channel (6B & 9B only) Remote 12 Volt power trigger input with
delayed output feature Selectable gain settings Optional 17" Faceplate (no
handles) or 19 inch rack mount (with handles) available. Optional Silver or
Black Faceplate Available
The
Bryston BP 1.5 C-Series Phono Stage With MPS-2 Power Supply The BP 1.5 is a high
quality, broadcast grade Phono Stage offering both Moving Magnet and Moving Coil
cartridge step-up capabilities. The BP 1.5 is available with an optional
outboard power supply - MPS-2 to minimize noise and distortion. It can also be
used with the power supply in a Bryston BP-26 Preamplifier without the need for
the extra power supply.1 pair Power supply input and outputs 1 pair RCA inputs
and outputs Outboard power supply Easy "shared" power supply with BP 26
ACCESSORI
Commutatore per due coppie di
diffusori con presa per cuffia
655 €
Commutatore per tre coppie di
diffusori con presa per cuffia
980 €
Commutatore per quattro coppie di
diffusori 1.060 €
Commutatore per sei coppie di
diffusori con montaggio rack 19”
1.540 €
Legenda istruzioni
Clicca
per qui per vedere : FOTO PRODOTTO
Clicca
per qui per vedere : ISTRUZIONI PRODOTTO
Clicca
per qui per vedere : CATALOGO,PROVA RIVISTE SPECIALIZZATE PRODOTTO
Clicca
per qui per vedere : DATI TECNICI SPECIFICHE
PRODOTTO
Attenzione
Per ordinare o avere
gli ultimi prezzi aggiornati telefona al
0174 670100
o invia un E-mail a info@sinergy.us
Il presente listino
sostituisce ed annulla ogni precedente.I prezzi indicati si
riferiscono a singolo diffusore.
Le caratteristiche e i prezzi indicati possono variare senza
preavviso telefonare o inviare un e-mail per ulteriori domande e
conferme sui prezzi sopra riportati.
Prezzi
franco
nostro magazzino
Nota bene Tutti i marchi citati nel presente listino sono di proprietà e
registrati alle rispettive Case Produttrici
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.gif)
.jpg){kind=small}
.gif)
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
.jpg){kind=small}
Clicca
per qui per vedere : FOTO PRODOTTO
Clicca
per qui per vedere : DATI TECNICI SPECIFICHE
PRODOTTO